Collection: Special Coatings

Black Bituminous paint

Product description

It is a hard glossy bitumen based paint to be used on any of the surface where a bituminous finish is required.

• Use: It is recommended for all metal surfaces as a finish coat and on wood and timber as both primer and top coat. It is also for steel structures in acidic environments, pipe wrapping with burlap or fiberglass underground and aboveground steel storage tanks.
• Finish: Silk black.
• Application: By brush or roller.
• Thinning and mixing: Thin with white spirit for brush or roller application.
• Equipment cleaning: Equipment should be cleaned immediately after use with white spirit.
• Drying time: 24 hours.
• Spreading capacity: 4-6m2 per litre.
•  Pack sizes: 1 litres, 4 litres.

 Chlorinated Rubber Paint

 Product description 

It is a hard wearing chemical resistant finish for use in areas where high chemical resistance is required e.g. in chemical factories, marine vessels, dairies, brewery etc.

• Uses: It can be applied on plaster, cement, steel, concrete and wooden surfaces. It is resistant to mild acids and alkalis. Recommended for use on swimming pools.
• Surface preparation: Iron and steel Prime the metal with zinc chromate primer. On galvanized iron and non-ferrous metals Prime with 1 coat of wash primer. On plaster and wood Prime with 1 coat of vinyl primer. Finish with 2-3 coats of chlorinated rubber paint.
• Finish: Gloss.
• Application: By brush or spray.
• Thinning and mixing: Chlorinated rubber paint thinner for brushing, synthetic thinner for spraying.
• Equipment cleaning: Equipment should be cleaned immediately after use with chlorinated rubber paint thinner.
• Drying time: 6 hours. Color range Pastel shades.
• Spreading capacity: 9-11m2 per litre at 40 microns DFT.
• Pack sizes: 1 litres, 4 litres and 20 litres.

 Road Marking Paint

Product description

It is manufactured especially for the painting of traffic lines for highways, streets, airports, factories, parking lots, etc. It is formulated with a synthetic binder which dries rapidly and gives maximum resistance to wear weather. It is also an excellent binder for beads, which may be easily added to the marking strip immediately after the traffic paint is applied and thickness of the applied layer.

• Surface preparation: Surface must be clean, dry and free from any loose material.
• Finish: Matt.
• Application: By brush or machine.
• Thinning and mixing: Road marking paint thinner. Equipment cleaning Road marking thinner.
• Drying time: 5-15 minutes.
• Color range: White and yellow.
• Spreading capacity: 5m2 per litre.
• Pack sizes: 1 litres, 4 litres.

 Aluminum Paint

Product description and uses

It is a special aluminium paint which, when painted on metal, will withstand temperatures of up to 3000C. When newly painted, the dry pyrofix paint film tends to powder slightly due to its special composition, but once the surface has been heated to a temperature of at least 2000C this effect will disappear. It does not need primer and can be brushed or sprayed directly on to clean, dry metal surface. Before use, the paint should be stirred thoroughly, replace the lid of the container tightly when not in use.

• Surface preparation: Surfaces to be painted must be clean, dry and free from grease, oil and rust. Rust and mill scale must be removed by scraping and wire brushing. For optimum results sandblasting is recommended.
• Finish: Metallic luster.
• Application: By brush or spray.
• Thinning and mixing: Thinned with mineral turpentine.
• Equipment cleaning: Equipment should be cleaned immediately after use with white spirit.
• Drying time: 1-2 hours at 200C. Color range Metallic grey with luster.
• Spreading capacity: 20-25m2 per litre at 15 microns.
• Pack sizes: 1 litres, 4 litres.

 2 Pack Epoxy

Product description and uses

It is a two component epoxy based enamel, highly resistant to chemical attack, with tremendous adhesion and resistance to both abrasion and impact. It is easy to apply and gives a waterproof film.

• Surface preparation: Surfaces must be clean, dry and free from oil, rust and paint. Aluminium sheet must be treated with a solution containing 1% phosphoric acid and then cleaned with water. Priming For metal, a coat of epoxy primer mixed with hardener should be applied. Primer should not be sanded due to lead content. For wood and concrete, the first coat should be thinned with 10% epoxy thinner. Apply 2-3 heavy coats of epoxy enamel mixed with hardener, allowing 24 hours drying time between all coats. Finish Gloss.
• Application: By brush or spray both epoxy primer and enamel should be mixed with hardener in the ratio of 2 parts primer or enamel to 1 part hardener by volume. Epoxy clear should be mixed with hardener in the ratio of 3 parts clear to 2 parts hardener by volume.
• Thinning and mixing: Should be thinned with epoxy thinner.
• Equipment cleaning: Epoxy thinner.
• Drying time: Dust dry in 2 hours and completely dry in 24 hour.
• Maximum resistance is achieved after three days.
• Color range: Epoxy-primer light grey epoxy enamel-white, light grey turquoise and clear.
• Spreading capacity: 8-10m2 per litre of mixture between the enamel and the hardener in the ratio of 3:1.
• Pack sizes: 1 litres, 4 litres. Pot life 6-8 hours.

2 Pack Epoxy Thinner

Product description and uses

It is a blend of organic solvents combined to give good solvency and flow properties in epoxy primer. Specific gravity 0.88. Flash point Above 210C.

• Color: Clear.
• Pack sizes: 1 litres, 5 litres.